Orderline: 01777 712661
Open: Mon-Fri 9am-5pm

Demo
Your shopping cart is empty!
Anaglypta - Luxury Vinyl Wildacre - RD803 Anaglypta Luxury Textured Vinyl Introduced in 1983 - Garden inspired vertical panel design available in luxury blown vinyl for easy .. Product #: RD803 based on 0 reviews Regular price: $8.13 $8.13 In Stock
Brand: Anaglypta - Luxury Vinyl
Product Code: RD803
Availability: In Stock

£9.76
Ex VAT: £8.13

Overview

Brand - Luxury Vinyl
Introduced in 1983 - Garden inspired vertical panel design available in luxury blown vinyl for easy application and provides an excellent surface for paint.

Features

  • Textured Warmth for walls and ceilings
  • Excellent surface for paint
  • Disguises imperfections
  • Uses paper from well managed sources

Specification

Coverage Roll Length Roll Width
 5.3m2  10m  0.53m

Match Type: Offset Match
Pattern Repeat: 32cm
Suitability: Walls & Ceilings

Recommended Paste

Easy Paste Ready Mixed
Each roll will require approximately 1kg of adhesive paste

Delivery

This item is available for next day delivery (same day dispatch*)
*on orders placed before 1pm

Features
Style Classic
Finish Textured
Specifications
Dimensions 53cm x 10m
Coverage 5.3m2
Match Type Offset Match
Material Pure paper, expanded vinyl composite
Additional Information
Suitability Walls & Ceilings
Recommended Paste Easy Paste Ready Mixed

Preparation

  • Surfaces painted prior to 1960 may contain lead pigments, special precautions should be taken during preparation.
  • To minimise the hazard in event of fire, do not hang wallcoverings over polystyrene veneers.
  • Keep room warm and well ventilated.
  • Turn electricity off at the main fuse box when working around switches, sockets, light fittings etc.
  • Remove any existing loose wallcoverings or linings.
  • Surfaces must be clean, smooth and dry.
  • Cure areas affected by either damp or mould at the source.
  • Pre-treat new plaster or other absorbent surfaces with a fungicidally protected adhesive or 'size'.
  • Roughen gloss painted surfaces with glass paper. Lining paper is recommended for uneven or contrasting surfaces.
  • Freshly painted surfaces should be left for at least 3 days prior to application.
  • We recommend a fungicidally protected wallpaper paste is used of possible, which should be mixed to the manufacturer's instructions. Ready mixed adhesives can also be used.

Application Guidance

FOR WALLS

  1. Measure 50cm (20") out from a corner. Avoid an area with windows or other details for the first strip if possible. Using a plumbline as a guide mark a vertical line from ceiling to floor N.B; Always ensure the width of the roll will be wide enough to fill the gap between the line and the corner, especially important in older properties where corners may not be perpendicular.
  2. Cut strips to length allowing extra for pattern match and trimming. Apply adhesive ensuring the entire reverse is well covered.
  3. Fold pasted sides inwards and leave to soak for 8-10 minutes. If the soaking time is extended be careful to ensure the paste does not dry out before application - apply extra paste if necessary.
  4. This product can be painted once the adhesive has fully dried out, normally after 24-48 hours.

FOR CEILINGS

(Application is similar to wall application)

  1. If a ceiling is not square it may be advantageous to consider hanging the strips across the shorter side for easier handling.
  2. Cut strips to length allowing extra for pattern match & trimming. Apply adhesive ensuring the entire reverse is well covered.
  3. Fold pasted sides inwards and leave to soak for 5 minutes. If the soaking time is extended be careful to ensure the paste does not dry out before application - apply extra paste if necessary.
  4. Position the paper on the ceiling following the guideline. Brush the paper onto the ceiling starting at the centre and brushing out towards the edges, expelling all air bubbles.
  5. Crease and trim at edges.
  6. Remove excess paste immediately with a damp sponge.
  7. Ensure subsequent lengths are applied in the correct direction use butt joints matching patterns as necessary. Ensure all lenghts are firmly adhered.
  8. This product can be painted once the adhesive has fully dried out, normally after 24-48 hours.
There are no reviews for this product.
Write a review
BadExcellent
Facebook comment